Women's Pants/US 8-12 l Plus Size Pants Sewing Pattern PDF | Curvy Fit High Rise Trousers | Womens Office Slacks with Pockets | M-XXL | Digital Download
1 / 6Interactive sewing map
Step-by-step technological process of sewing the garment.
1
Page 6
Interfacing the Pattern Pieces
- Fuse the pattern pieces from the wrong side as follows: Welts, Pocket facings, and Waistband.
2
Page 6
Interfacing the Fly and Pocket Openings
- Attach the adhesive fly facing to the seam allowance on the right front pant leg from the wrong side. On the seam allowance of the left front pant leg, apply a 1 cm wide strip of fusible interfacing. Attach a 1.0 cm wide strip of interfacing to the pocket opening seam allowance on the wrong side.
3
Page 7
Sewing Back Waist Darts
- Sew the waist darts on the back pieces of the pants, then press the dart seam allowances toward the center back.
4
Page 8
Marking Back Welt Pocket Placement
- Mark the placement of the welt pocket on the back pieces of the pants from the right side, following the markings on the back piece template.
5
Page 9
Attaching the Welt to the Pocket Frame
- Sew the welt to the pocket frame line, following the marked chalk line exactly and checking the ends of the pocket frame as you go.
6
Page 11
Cutting the Pocket Opening
- Cut along the marked pocket entry lines on the back pant piece and the upper pocket lining, stopping 1.5 cm short of both ends, then cutting at a 45-degree angle toward the corners.
7
Page 18
Preparing Side Pocket Facings
- Finish the rounded outer edges of the pocket facing and pocket trim with an overlock stitch.
8
Page 22
Stitching Pocket Lining Bags
- Sew the rounded edges of the burlap pocket bags together with a double stitch, using a 1.0 cm seam allowance.
9
Page 24
Sewing Bottom Leg Darts
- Sew the darts along the bottom edges of the front and back pant legs.
10
Page 25
Assembling Side Seams
- Sew the side seams of the pants with a 1.0 cm seam allowance, matching the edges and notches with right sides facing each other.
11
Page 27
Sewing Inseams
- Sew the inseam edges of the pants together, allowing a 1.0 cm seam, and finish the seam allowances.
12
Page 29
Sewing the Seat Seam
- Sew the seat seam with a double stitch up to the indicated point where the fly begins, using a 1.0 cm seam allowance.
13
Page 34
Attaching Zipper to Left Fly
- Attach one side of the zipper tape to the edge of the fly on the left pant leg using a single presser foot with a 1.0 cm seam allowance.
14
Page 36
Stitching the Decorative Fly Topstitch
- Stitch along the marked line from the top edge of the pants, stopping 1.0–1.5 cm before the center seam, folding the facing to the inside. Secure the end with a backstitch.
15
Page 40
Attaching Belt Loops
- Sew the belt loops onto the top edge of the pants, following the markings on both the front and back pieces. Use a seam allowance of 0.5 cm.
16
Page 41
Attaching the Waistband
- Attach the outer edge of the waistband to the top edge of the pants with a 1.0 cm seam allowance.
17
Page 45
Hemming the Pants
- Sew a decorative stitch along the bottom of the pants, 3.8 cm from the pressed edge, or hem the bottom with invisible stitches.
18
Page 46
Sewing the Button
- Mark the spot for attaching the button on the left end of the belt and sew on the button.
