Women's Pants/Tapered Suit Pants Sewing Pattern: Mid-Waist Trousers (XS-XXL) (Digital Download)
1 / 5Interactive sewing map
Step-by-step technological process of sewing the garment.
1
Page 8
Sewing Back Waist Darts
- Sew the waist darts on the back pieces of the pants.
2
Page 8
Marking and Sewing Back Waist Darts
- Mark the position for the waist dart and the welt pocket on the reverse side of the back pant pieces.
3
Page 9
Marking Welt Pocket Position
- Mark the position of the welt pocket on the back pieces of the pants from the right side, following the markings on the back piece template.
4
Page 10
Stitching the Pocket Flap
- Stitch the flap to the pocket frame line, making sure to follow the marked line and align the ends of the pocket frame precisely.
6
Page 12
Cutting Pocket Opening
- Cut the back pant pieces and the upper pocket bag along the marked pocket opening lines.
7
Page 13
Stitching Flap to Top Lining
- Stitch the pressed edge of the flap to the top lining, keeping a 0.1 cm seam.
8
Page 15
Topstitching Facing to Bottom Lining
- Topstitch the pressed edge of the facing onto the bottom pocket lining, staying 0.1 cm from the edge.
9
Page 16
Sewing Pocket Bag Pieces
- Sew the burlap pieces together. Allowance: 1.0 cm.
10
Page 18
Finishing Pocket Facing and Trim Edges
- Finish the edges of the pocket facing and side pocket trim with an overlock stitch.
11
Page 19
Stitching Pocket Facing to Upper Lining
- Stitch the pocket facing onto the upper pocket lining, following around the edge of the facing. Leave a seam allowance of 0.3 cm.
12
Page 20
Sewing Front Waist Darts
- Sew the waist darts on the front pant legs.
13
Page 21
Pressing Side Pocket Opening
- Press the pocket opening, forming a 0.1 cm roll from the front panel piece.
14
Page 22
Sewing Side Pocket Bag
- Sew the rounded edges of the burlap with a double stitch. Allow a seam margin of 1.0 cm.
15
Page 24
Sewing Bottom Darts
- Sew the darts along the bottom edge of the front and back pant pieces.
16
Page 25
Sewing Side Seams
- Sew the side seams of the pants, leaving a 1.0 cm seam allowance.
17
Page 27
Sewing Inseams
- Sew the pant inseams together, leaving a 1.0 cm seam allowance.
18
Page 29
Sewing Seat Seam
- Sew the seat seam with a double stitch up to the marked starting point of the fly. Seam allowance: 1.0 cm.
19
Page 33
Pinning Zipper Tape
- Pin one side of the zipper tape to the edge of the left fly. The top stop of the zipper should be 1.2 cm below the top edge of the pants. The lower stopper should sit 2 mm above the seat seam stitch line.
20
Page 34
Stitching Fly Facing
- Stitch the facing to the left side of the fly using a single presser foot. Seam allowance: 1.0 cm.
21
Page 36
Sewing Decorative Fly Topstitch
- Sew the decorative topstitch on the fly in two steps: 1) Following the marked line from the top edge of the pants, stop 1.0–1.5 cm before reaching the center seam, folding back the facing on the inside. Secure with a backstitch at the end.
22
Page 38
Topstitching Belt Loops
- Topstitch along both edges of the belt loop at 0.1 cm.
23
Page 41
Attaching Waistband
- Attach the outer edge of the waistband to the top edge of the pants. Seam allowance: 1.0 cm.
24
Page 43
Securing Belt Loops
- Secure the belt loops by stitching them 0.5 cm away from the waistband seam.
