Women's Blazers/Kimono Blazer Pattern PDF | Wrap Jacket Sewing | Collarless Oversized Coat | Minimalist Linen Outerwear | XS-M
.webp)
1 / 6Interactive sewing map
Step-by-step technological process of sewing the garment.
1
Page 1
Stay Tape Application
- Fuse the stay tape to the front neckline's bias edge from the wrong side.
2
Page 1
Interfacing
- Apply interfacing to the cut pieces from the wrong side: front facings, the back neckline facing.
3
Page 1
Sleeve Hem Preparation
- Press the sleeve hem allowance up by 1.0 cm.
4
Page 2
Shoulder Seams Sewing
- Sew the shoulder edges together. Seam allowance 1.0 cm.
5
Page 2
Shoulder Seams Finishing
- Serge the seam allowances of the shoulder seams.
6
Page 2
Shoulder Seams Pinning
- Pin the shoulder edges together, matching the right sides.
7
Page 2
Sleeve Hem Pressing
- Then repeat at 4.0 cm, turning the seam allowance to the wrong side.
8
Page 3
Sleeve Seam Finishing
- Finish the seam allowances on the sleeve-to-armhole seam.
9
Page 3
Sleeve Sewing
- Sew the sleeves into the armholes, easing the back and front slightly. Seam allowance: 1.0 cm.
10
Page 3
Sleeve Pinning
- Pin the sleeves to the armhole, matching the edges and notches, with right sides together.
11
Page 3
Shoulder Seams Pressing
- Press the shoulder seam allowances toward the back.
12
Page 4
Sleeve and Side Seam Sewing
- Sew the sleeve-side seam edges together. Seam allowance: 1.0 cm.
13
Page 4
Sleeve and Side Seam Finishing
- Finish the seam allowances on the sleeve-side seams.
14
Page 4
Sleeve and Side Seam Pinning
- Pin the sleeve-and-side seam edges together, matching the raw edges and placing right sides together.
15
Page 4
Sleeve Seam Pressing
- Press the seam allowances from attaching the sleeve to the armhole toward the front and back armholes.
16
Page 5
Sleeve and Side Seam Pressing
- Press the seam allowances of the sleeve-and-side seams toward the back.
17
Page 5
Sleeve Hem Pinning
- Pin the pressed allowance at the sleeve hem. Baste if needed.
18
Page 5
Sleeve Hem Topstitching
- Sew a topstitch along the sleeve hem, stitching 3.8 cm in from the edge.
19
Page 6
Facing Shoulder Seams Pressing
- Press open the seam allowances of the shoulder seams on the front facing and the back neckline facing.
21
Page 6
Facing Shoulder Seams Pinning
- Pin the shoulder seams of the back neckline facing to the front facings, aligning the edges with right sides together.
22
Page 6
Facing Shoulder Seams Sewing
- Sew the shoulder seams of the back neckline facing to the front facings. Seam allowance: 1.0 cm.
23
Page 7
Facing Inner Seam Pressing
- Press the inner seam allowances of the front facing, clipping the seam allowance at the corner of the front edge, and the back neckline facing. Clip the curved, pressed seam allowance, stopping 2-3 mm short of the fold.
24
Page 8
Facing Template Pressing
- Press the facing seam allowance using a template made from the back-neck facing pattern piece, without the inner seam allowance.
25
Page 8
Facing Pinning
- Pin the front facing and attach the back-neck facing to the front edge and to the neckline of the front and back pieces, matching the raw edges, seams, and notches, with right sides together.
26
Page 9
Facing Stitching
- Stitch the front opening edges with the facings. Finish the neckline of the front and back with the neckline facing. Seam allowance: 0.7 cm.
27
Page 9
Trimming Seam Allowances
- Trim the seam allowances at the corners of the front-edge facing seam.
28
Page 10
Trimming Shoulder Seams
- Trim the seam allowances at the shoulder seams to reduce bulk.
29
Page 10
Clipping Neckline Curves
- Clip the seam allowance of the back neckline facing at the curves.
30
Page 10
Facing Topstitching
- Topstitch the seam allowance of the front edge facing from the front facing side and the seam allowance of the front and back neckline facing from the back neckline facing side at 0.1 cm.
31
Page 11
Pressing Faced Seams
- Press the faced front edge seams and press the front and back neckline, forming a 0.1 cm roll to the outside from the front and back pieces.
32
Page 11
Garment Hem Pressing
- Press the hem allowance along the bottom edge of the garment by 1.0 cm and again by 4.0 cm, turning the seam allowance to the wrong side.
33
Page 12
Pinning Lower Facing Edge
- Pin the lower edge of the facing to the bottom of the front panel's front edge, turning it to the wrong side along the stitched edge and aligning the lower raw edges.
34
Page 12
Clipping Lower Seam Allowance
- Clip the seam allowance at the bottom of the front edge.
35
Page 12
Stitching Lower Front Edge
- Stitch the lower front edge along the pressed fold.
36
Page 13
Turning and Pressing Corner
- Turn the stitched corner of the front edge to the right side and shape it neatly. Press the stitched corner, forming a 0.1 cm turn of cloth along the bottom from the front piece.
37
Page 13
Pinning Back Neckline Facing
- Pin the pressed inner edge of the back neckline facing to the back panel. If needed, baste the seam allowance.
38
Page 13
Pinning Inner Facing Edge
- Pin the pressed inner edge of the front facing and the lower seam allowance to the front piece. If needed, baste the seam allowance.
39
Page 14
Topstitching Front Edge
- Sew a topstitch along the front edge, the back and front neckline, as well as the garment hem along the marked line. Remove the basting threads.
40
Page 14
Marking Topstitch Line
- Mark the topstitch line along the front edge and the garment hem along the neckline of the front and back, keeping 3.8 cm from the edge.
41
Page 15
Final Pressing of Topstitching
- Press the topstitched front-edge seams, the neckline on the front and back, and the garment hem.
42
Page 16
Marking Button Placement
- Mark the buttonhole and button placement along the right and left front edges, following the markings on the front pattern piece.
44
Page 17
Sewing Buttons
- Sew on the buttons on the right and on the left front panels.
45
Page 17
Cleaning Buttonholes
- Clean the buttonholes on the front panels.
46
Page 18
Sewing Hidden Button
- Sew a hidden button to the wrong side of the right front panel, aligning it with the button placement marked on the right side.
