Women's Sweatshirts/Hoodie sewing pattern | Anorak sewing pattern | Warm pattern | PDF Pattern | XS - XXL | A4, Plotter, letter | Hoodie Schnittmuster
1 / 8Interactive sewing map
Step-by-step technological process of sewing the garment.
1
Page 5
SLEEVE ASSEMBLY
- Fold the sleeve with the right sides together, aligning the top edges, and pin in place. Stitch the upper edges of the sleeve with an overlock machine along the elbow side, removing the pins as you go. Important! At the end of the seam, leave a thread chain and tuck it into the seam using a hook.
2
Page 5
SLEEVE ASSEMBLY
- Secure the top of the upper seam on a straight-stitch machine, stitching directly along the overlock seam.
3
Page 6
SLEEVE ASSEMBLY
- Press the seam allowance of the upper sleeve seam toward the front of the sleeve. At the top of the seam, gently steam out any excess fabric.
4
Page 6
SLEEVE ASSEMBLY
- Place the front piece and the sleeve right sides together, aligning the armhole edge with the sleeve cap edge, and secure them with pins. Using an overlocker, sew the sleeve into the front armhole along the front piece, removing each pin as you go.
5
Page 6
SLEEVE ASSEMBLY
- Mark a section on the sleeve seam and sew a reinforcing stitch along it. Remember to backstitch at the beginning and end.
6
Page 7
SLEEVE ASSEMBLY
- Place the front piece and sleeve right sides together, aligning the armhole edge with the sleeve cap edge. Pin in place. Stitch the sleeve into the front armhole using an overlocker, removing pins as you go.
7
Page 7
SLEEVE ASSEMBLY
- Press the seam allowances of the sleeve attachment toward the sleeve.
8
Page 8
SLEEVE ASSEMBLY
- In the same way, attach the sleeve to the back armhole.
9
Page 9
Collar Stand Finishing
- Use a serger to finish the lower edge of the inner collar from the right side.
10
Page 9
Collar Stand Finishing
- Place the inner and outer collar bands together with their right sides facing, aligning the top edges. Secure with pins. Stitch the collar bands together on a straight stitch machine with a 7 mm seam allowance, removing the pins as you go.
11
Page 10
Collar Stand Finishing
- Press the seam allowances of the collar stand towards the inner stand, then topstitch from the right side, keeping 2 mm away from the seam.
12
Page 10
Collar Stand Finishing
- Place the collar stands with their right sides facing out, press them, and shape the edge from the outer stand piece.
13
Page 11
Collar Stand Finishing
- Unfold the collar band along the pressed crease. Place the outer band right sides together with the garment, matching the notches on the band to the joining seams and the top sleeve seam. Align the lower edge of the outer band with the neckline edge and pin in place. Sew the outer band to the neckline with a serger, removing the pins as you go.
14
Page 11
Collar Stand Finishing
- Press the seam allowances of the collar stand toward the stand.
15
Page 12
Collar Stand Finishing
- Finish the armhole edge of the inner upper front piece with an overlock stitch from the right side. Press to set the seam.
16
Page 13
Collar Stand Finishing
- Place the inner collar stand and the inner upper front together with the right sides facing each other, aligning the neckline edge of the inner upper front with the bottom edge of the inner collar stand. Pin in place. Stitch on a straight stitch machine, keeping a distance of 7 mm from the edges.
17
Page 13
Collar Stand Finishing
- Press the seam allowance of the inner collar stand towards the inner upper front.
18
Page 14
ZIPPER PROCESSING
- Finish the lower edge of the outer upper front piece from the inside using a serger, 5-7 cm from the center cut.
19
Page 14
ZIPPER PROCESSING
- Serge the lower edge of the inner front upper piece from the right side, 5–7 cm out from the center edge.
20
Page 14
ZIPPER PROCESSING
- Place one side of the zipper right sides together with the garment, aligning the zipper tape with the center edge of the front upper piece and the outer stand. Position the top zipper stop 2 mm below the collar seam, and the bottom stop 8–9 mm above the lower edge of the front upper piece. Baste the zipper in place.
21
Page 15
ZIPPER PROCESSING
- Fold the lower end of the zipper inside with the inner placket and the inner upper front piece, and secure with pins.
22
Page 15
ZIPPER PROCESSING
- Stitch along the zipper with a straight stitch, keeping 2–3 mm away from the zipper teeth and using the special presser foot. Remove the basting threads when finished.
23
Page 15
ZIPPER PROCESSING
- Stitch the zipper in place using the inner placket and the inside upper front piece. Sew along the zipper attachment seam on a straight-stitch machine, then remove the pins.
24
Page 16
ZIPPER PROCESSING
- Align the lower edges of both the outer and inner front pieces.
25
Page 16
ZIPPER PROCESSING
- Turn the collar right side out, shape the corner, and press it flat. Mark a guideline for collar symmetry on the second half of the zipper.
26
Page 16
ZIPPER PROCESSING
- Unzip the zipper. Repeat the process for the other side, aligning the marked guideline on the zipper with the collar seam. Press the zipper lightly to set it in place.
27
Page 17
ZIPPER PROCESSING
- Secure in place with pins. Sew the seam allowances together on a straight-stitch machine, keeping a 3-5 mm distance, and remove the pins as you go.
28
Page 18
ZIPPER PROCESSING
- In the same way, pin together the armhole edges of the upper front pieces (both outer and lining) as close to the neckline as possible.
29
Page 18
ZIPPER PROCESSING
- Pin together the outer and inner collar pieces.
30
Page 19
ZIPPER PROCESSING
- Stitch along the seam groove where the upper collar is attached, removing pins as you go.
31
Page 20
Finishing the Front Horizontal Seam
- Align the top and bottom front pieces with the horizontal edges matching, then pin them together.
32
Page 20
Finishing the Front Horizontal Seam
- Measure 5 centimeters out from the center of the piece on each side. Finish the marked section with a serger.
33
Page 21
Finishing the Front Horizontal Seam
- Using a narrow presser foot, stitch the central section of the upper and lower front pieces (already serged) together on a straight-stitch machine, keeping the seam width at 7 mm.
34
Page 22
Finishing the Front Horizontal Seam
- Press the seam allowances of the front sections toward the lower part.
35
Page 22
Finishing the Front Horizontal Seam
- Using a serger, join the upper and lower front pieces along the edge of the upper section in two passes. The serger stitch should overlap the previously finished areas by 2–3 cm.
36
Page 23
Finishing Side Seams and Sleeve Seams
- Turn the garment inside out. Align the notches and the sleeve attachment seam, matching the side edges of the front and back pieces and the sleeve edges, then secure with pins. Using an overlock machine, sew the side and sleeve edges in one continuous seam from the front side, removing pins as you go.
37
Page 23
Finishing Side Seams and Sleeve Seams
- Press the seam allowances of the side seams and sleeve seams toward the back piece.
38
Page 24
Finishing the Hem of the Garment and Sleeves
- Use the pattern to measure the hem allowance, then mark the hem line on the right side of the sleeve and along the bottom edge of the garment.
39
Page 24
Finishing the Hem of the Garment and Sleeves
- Serge the bottom edge of the garment and sleeves.
40
Page 24
Finishing the Hem of the Garment and Sleeves
- Fold the allowance under and stitch along the marked line.
41
Page 25
Finishing the Hem of the Garment and Sleeves
- Stitch the hem of the garment using a flatlock machine or a double needle on a straight stitch machine. Guide the far-left needle along the marked line. Remove any basting threads afterward.
